Product Data Sheet Safety Data Sheet Show all documents
SikaQuick® Concrete Resurfacer

SikaQuick® Concrete Resurfacer

High Performance, Fast Setting, Cement-based resurfacer

SikaQuick Concrete Resurfacer is a polymer-modified, 1-component, cementitious resurfacing compound. Designed for use on exterior concrete substrates such as sidewalks, walkways, patios, parking garages, and residential driveways. Easily applied by smoothing trowel or rubber squeegee.

  • Easy to use, one-component.
  • Variable water ratios for different use: resurfacing/sloping.
  • Interior and exterior use.
  • Feather edge application.
  • High abrasion resistance.
  • Foot traffic in 2-3 hours.
  • Freeze/thaw resistant.
  • 28 days compressive strength (ASTM C-109)-3,500 psi ( 24.1 MPa).
Product Data Sheet Safety Data Sheet Show all documents

Usage

  • To be used on concrete, above and below grade.
  • Use on horizontal surfaces, both interior and exterior.
  • Use as a protective coating to reduce the effect of deicing salt on concrete.
  • Use as a coating over newly repaired concrete to provide a uniform appearance.
  • Use on concrete and masonry substrates to improve abrasion resistance to foot traffic and tire traffic.
 

Advantages

  • Easy to use, one-component.
  • Variable water ratios for different use: resurfacing/sloping.
  • Interior and exterior use.
  • Feather edge application.
  • High abrasion resistance.
  • Foot traffic in 2-3 hours.
  • Freeze/thaw resistant.
  • 28 days compressive strength (ASTM C-109)-3,500 psi ( 24.1 MPa).

Packaging

35 lbs. ( 15.9 kg.)

Color

Cement-gray

Product Details

Product Information

Shelf Life

12 months from date of manufacture if stored properly in original, unopened and undamaged, sealed packaging

Storage Conditions

Store in a cool, dry area. Do not leave bags exposed to the sun.

Application

Application Information

Mixing Ratio

6.0 - 6.5 pints (2.8 -3.1 L)

Layer Thickness

Feather edge to 1/2"

Ambient Air Temperature

45°-95°F (7°-35°C)

Pot Life

Approximately 20 minutes

Waiting / Recoat Times

16 - 24 hours
Consumption

Coverage

 13-16 ft2 at 1/4" (1.2-1.5 m2 at 6 mm) per bag
Application steps

MIXING

  • Wet down all tools and mixer to be used.
  • Pour 6.0 - 6.5 pints ( 2.8 - 3.1 liters) of clean water into a suitably sized mixing container.
  • Add the entire bag's contents of SikaQuick® Concrete Resurfacer to the mixing water while continuously mixing with a low-speed rotary drill (400-600 rpm) and paddle.
  • Do not overwater as excess water may result in difficulty handling and/or not meeting stated typical physical performance values.
  • Mix to a uniform consistency, maximum 3 minutes.

APPLICATION

  • SikaQuick® Concrete Resurfacer should be applied in one pass in thicknesses ranging from a true feather edge to 1/2 inch (13 mm) in depth.
  • The placed material may be troweled, floated or broom finished.

CURING TREATMENT

  • As per ACI recommendations for Portland cement concrete, curing is required.
  • Moist cure with wet burlap and polyethylene, a fine mist of water or Sika® Antisol®-250W*.
  • Curing compounds adversely affect the adhesion of following lifts of mortar, leveling mortar or protective coatings.
  • Moist curing should commence immediately after finishing. Protect freshly applied mortar from direct sunlight, wind, rain, and frost.

*pretest of curing compound is recommended

Documents