Product Data Sheet
Show all documents
SikaWall®-6260 Metallic F1.0 Finish

SikaWall®-6260 Metallic F1.0 Finish

Factory-mixed, 100% acrylic polymer finish, utilizing uniformly sized 1 mm aggregate for a fine texture. It features an optimized combination of aggregates and metalescent pigments that combine the visual appeal of metal with the application ease of a textured finish.

  • Metal pigmentation and optimized aggregate size provide a metal sheen.
  • Abrasion resistant to enhance the metallic appearance, increase ease of application, and hide minor surface imperfections.
  • Integral color and reduced maintenance.
Product Data Sheet
Show all documents

Usage

SikaWall Metallic F1.0 finish provides protection for an aesthetically pleasing metallic appearance, surface and texture for Sika Facades systems, poured concrete or unit masonry, conventional stucco, properly prepared insulating concrete forms, and interior veneer plaster or gypsum wallboard.  

Advantages

  • Metal pigmentation and optimized aggregate size provide a metal sheen.
  • Abrasion resistant to enhance the metallic appearance, increase ease of application, and hide minor surface imperfections.
  • Integral color and reduced maintenance.

Packaging

5 gallon pail (19 liters)

Color

Available in a range of standard and custom colors.

Product Details

Product Information

Shelf Life

Two (2) years, when properly stored in the original container.

Storage Conditions

  • Store in a cool, dry place protected from freezing, extreme heat and direct sun. Store at no less than 40°F (4.5°C).
  • Do not stack pallets.

Volatile organic compound (VOC) content

ASTM D3960 (based in part on EPA Method 24)

<50g/l less water and exempt solvents
Technical Information

Abrasion Resistance

METHOD

CRITERIA

RESULT

ASTM D968

No cracking or loss of film integrity at 528 qt. (500L) of sand

Finish not worn through after 725 qt. (686L) of falling sand

Tensile Adhesion Strength

ASTM C297, E2134

15 psi minimum

> 15 psi

Behavior after Artificial Weathering

Accelerated Weathering

ASTM G23

 

 

2000 Hours

 

 

Pass

ASTM G53

7500 Hours

Pass

Permeability to Water Vapor

ASTM E96 Method B

Report Value

Finish with Sika Facades wet base coat and 4 oz reinforcing mesh: 15.1 Perms

Salt spray resistance

ASTM B117

300 Hours

Pass

Water resistance

ASTM D 2247

No deleterious effects after 14 days of 100% R.H. exposure

Pass

Application

Application Information

Ambient Air Temperature

  • Protect from temperatures less than 40°F (4.5°C) for a minimum of 24 hours or until dry
  • When temperatures less than 40°F (4.5°C) prevail, provide supplementary heat during installation and drying period for at least 24 hours after installation and until dry.
  • Do not apply in ambient temperature above 100°F (38°C) or surface temperature above 120°F (49°C).

Substrates

  • Sika Facades' Systems
  • Poured Concrete or Unit Masonry
  • Conventional Stucco
  • Interior Veneer Plaster or Gypsum Wallboard

Drying Time

Under average conditions [70°F (21°C), 50% Relative Humidity

  • Finish will be dry within 24 hours. Drying time is dependent on humidity, air temperature, sun exposure, surface conditions and finish thickness. Lower temperature, higher humidity and application in shaded areas will extend drying time.
  • Protect finish from rain or other precipitation and temperatures less than 40°F (4.5°C) for a minimum of 24 hours and until dry.
 
Consumption

Coverage

125-135 ft2 (11.6-12.5 m2) per pail 

Coverage rates vary depending on the porosity of substrates and application techniques.

Documents