SikaWall® Fog Coat

• Binder Base: White Portland Cement: ASTM C150 Type I, Type-S Hydrated Lime: ASTM C206.
• Color: White or tinted to desired color.
• VOC-Compliant. Meets SCAQMD Rule 1113 when using SikaWall Color Packs.

12 months from date of production if stored properly in original, unopened and undamaged sealed packaging.

Store dry, off ground and protect from rain and moisture.

• Lightly mist wall with water to dampen 24 hours after application of SikaWall® Fog Coat to assist curing – allow to dry.
• Repeat step one several times. This is essential during dry and/or hot weather.
• Complete curing requires several days, and normal chalkiness will decrease as curing takes place.
• The use of SikaWall-73 Adacryl Admix & Bonder as described in the Mixing Instructions will reduce the occurrence of the normal chalkiness. Using the maximum amount of SikaWall-73 Adacryl Admix & Bonder will eliminate the need to moist cure.

Note: SikaWall Fog Coat is designed to revitalize existing stucco colors. To change colors or for application over smooth or unusual surfaces, use SikaWall Allegro II Cement Coating.

Approximately 1 hour depending upon temperature, humidity and substrate. High humidity and low temperatures extend drying time. Can be recoated after drying.

Depending on the condition of the substrate, method of application, amount of water used per bag and number of applications. Approximate coverage when two coats are applied is: 800 to 1,000 ft2 (74-93 m2) per 25 lb. (11.3 kg) bag.

• Stucco must be clean, free of dirt and foreign material.
• Remove surface contaminants such as dust or dirt without damaging the substrate.
• NOT recommended for application over painted, sealed, wood, metal or smooth surfaces.
• SikaWall® Fog Coat should be applied with an ambient and surface temperature above 40°F (4°C) for a minimum of 24 hours following the application.

• Read the entire label before using this product.
• Use clean equipment for mixing and preparation. While stirring using a drill at 400–500 rpm with a rust free mixing paddle, slowly add the 25 lb. bag of SikaWall® Fog Coat to 2-½ gallons of cool-clean potable water.
• Let the material sit for approximately 10 minutes and remix to ensure the product and color are well dispersed.
• Divide equally into two 5 gallon pails.
• Add an additional 1-½ to 2-½ gallons of water to each pail, each 25 lb. bag of Fog Coat will yield a total of 8 to 10 gallons of mixed product.
• Stir thoroughly and strain the SikaWall® Fog Coat material through a suitable paint strainer in a clean 5-gallon pail or spray equipment tank to be used. Do not ring out strainer. 
• If desired, add SikaWall-73 Adacryl Admix & Bonder, 6-10 ounces per gallon (maximum of 1 gallon per bag in place of the equivalent amount of water) of mixed, strained SikaWall® Fog Coat.
• Agitate material frequently to avoid seperation during application.

• Before applying this product, a sample should be applied and allowed to cure for color approval. The color level can be adjusted at this time by adding a small amount of additional color pigment from a SikaWall Color Pack of the same color.
• While spraying use a circular motion when using a circular pattern tip, or alternate vertical and horizontal motions when using a fan pattern tip, holding the nozzle 18” from the wall.
• Apply end to end and top to bottom or to a prominent architectural break.
• Two coats are recommended to ensure complete coverage.
• SikaWall® Fog Coat over-spray, drips, or spills should be removed immediately with water, or soap and water to prevent the possibility of permanent staining