Product Data Sheet
Show all documents
Sikafloor® Marine-595

Sikafloor® Marine-595

Self-leveling decorative resin with low thermal conductivity

Sikafloor® Marine-595 is a self-levelling aliphatic 2-component polyurethane decorative floor resin. It is part of the Sikafloor® Marine Deco systems for exterior use.
If the Sikafloor® Marine-595 needs to be accelerated, Sikafloor® Marine-001 or -002 can be used.  

  • Good application characteristics
  • Low thermal conductivity
  • Low density
  • Patented Sika Cool technology
  • Solvent-free
  • Longterm elastic
  • Very high yellowing resistance
  • Very low VOC emission
  • Acceleration option available
 
Product Data Sheet
Show all documents

PRODUCT BENEFITS

  • Good application characteristics
  • Low thermal conductivity
  • Low density
  • Patented Sika Cool technology
  • Solvent-free
  • Longterm elastic
  • Very high yellowing resistance
  • Very low VOC emission
  • Acceleration option available
 

Usage

Sikafloor® Marine-595 is designed as part of the Sikafloor® Marine Deco systems as synthetic teak decking solution with patented Sika Cool Technology, for external decks in shipbuilding, cruise and leisure boat construction. This product is suitable for experienced professional users only. Tests with actual substrates and conditions have to be performed ensuring workability, adhesion and material compatibility.  

Packaging

Sikafloor® Marine-595 (A)

Pail

8.2 kg

Sikafloor® Marine-595 (B)

Pail

5 kg

Product Details

Typical Product Data
Properties

Sikafloor® Marine-595 (A)

Sikafloor® Marine-595 (B)

Chemical base

Polyurethane

Isocyanate

Color (CQP001-1)

 

mixed

Colored

Transparent

Various colors available (see color design chart)

Density

 

mixed

0.86 kg/l

1.16 kg/l

0.97 kg/l

Solid content

100 %

Mixing ratio

by weight

41 : 25

Application temperature

substrate / climate

15 ─ 30 °C A, B

Shore A hardness (CQP023-1 / ISO 48-4)

90

Tensile strength (DIN 53504)

8.5 MPa

Elongation at break (DIN 53504)

50 %

Pot-life

15 °C

20 °C

30 °C

120 minutes

90 minutes

60 minutes

Shelf life

9 months C

12 months C

CQP = Corporate Quality Procedure

A) substrates must be 3 °C above the dew point

B) max. 80 % r.h.C) stored in sealed container in up-right position in a dry place between 5 and 30 °C, protected from direct sunlight
Technical Information

CURE MECHANISM

The curing of Sikafloor® Marine-595 takes place by a chemical reaction of the two components.
Higher temperatures speed up and lower temperatures slow down the curing process.

CHEMICAL RESISTANCE

For advice contact the Technical Department of Sika Industry.

Application

Application Information

Surface Preparation

Sikafloor® Marine-595 is installed on top of the deck levelling compound.
Metallic decks need to be prepared to SA 2.5 (ISO 8501). Aluminum decks must not be shot blasted. The prepared metallic surfaces need to be clean, free of dirt, grease, oil and loose particles before the SikaCor® ZP Primer is applied.
The application area must be protected against weather and direct sunlight.

Application

Sikafloor® Marine-595 is poured and spread evenly by means of a notched trowel, flat trowel or pin-rake. In critical areas a spike roller can be used to improve levelling and de-airing. For deeper sections (e.g. unevenness), it might be necessary to pre-level these sections. Ensure the pre-leveled sections have achieved "foot traffic" cure level prior to proceeding.

 

For liquid application on cambers and slopes multiple applications steps may be needed. Curing speed depends on temperature and layer thickness. Always consider the pot life to keep a wet edge.

Curing

Indications regarding curing details see table below:

Tempera-
ture

Foot traffic

Light trafficA

Full cure

15 °C

16 hours

32 hours

48 hours

20 °C

12 hours

16 hours

48 hours

30 °C

8 hours

12 hours

24 hours

A) food trolleys and light rolling equipment on soft wheels

Removal

Uncured Sikafloor® Marine-595 can be removed from tools and equipment with Sika® Colma Cleaner or another suitable solvent. Once cured, the material can only be removed mechanically.

Hands and exposed skin shall be washed immediately using hand wipes such as Sika® Cleaner-350H or a suitable industrial hand cleaner and water.

Do not use solvents on skin.

Application Limits

Freshly applied Sikafloor® Marine-595 must be protected from moisture, condensation and water for at least 1 day. Uncured material reacts in contact with water (foaming).

STORAGE CONDITIONS

Both components of Sikafloor® Marine-595 have to be kept between 5 °C and 30 °C in a dry place. Do not expose it to direct sunlight. After opening of the packaging, the contents need to be protected against moisture.

Minimum temperature during transportation is 5 °C.

Documents