Sika Thoroseal®-582 F

Sika Thoroseal®-582 F contains cement, graded sand, and proprietary additives.

1 year when properly stored

Transport and store Sika Thoroseal®-582 F in unopened containers and keep them in a clean, dry place protected from rain, dew, and humidity. Do not stack bags more than two pallets high. Store Sika Thoroseal® Acryl 60 in similar conditions. Do not allow Sika Thoroseal® Acryl 60 to freeze.

Specific gravity

1.2

225 ft²/50 lb bag (20.9 m²/22.7 kg bag) as a base coat at 1⁄16" (1.6 mm) dry-film thickness.
450 ft²/50 lb bag (41.8 m²/22.7 kg bag) as a topcoat at 1⁄32" (0.8 mm) dry-film thickness.

Coverage will vary depending on surface texture and porosity.

• Sika Thoroseal®-582 F must be modified with Sika Thoroseal® Acryl 60 to achieve the properties listed in the product data sheet.
• For NSF applications, refer to the Sika Thoroseal®-582 F data sheet
• Do not apply to substrates with active water leaks or moving cracks.
• Maintain or place expansion and control joints as necessary.
• Do not apply in rain or when rain is expected within 24 hours. Do not apply above 90°F (32°C) or below 40°F (4°C) or when temperatures are expected to fall below 40°F (4°C) within 24 hours. For hot and cold temperature applications, store Sika Thoroseal®-582 F, Sika Thoroseal® Acryl 60, and water at 50 to 70°F (10 to 21°C) before use.
• Windy, dry, or hot conditions may require rewetting of Sika Thoroseal®-582 F during cure and the use of polyethylene barriers.
• Before specifying Sika Thoroseal®-582 F for water-retaining structures, conduct tests to determine water quality. Sika Thoroseal®-582 F is not intended for continuous contact with acid or sulfate-containing water. Very soft water will have an adverse effect on Sika Thoroseal®-582 F.
• Service temperatures: immersion, up to 140°F (60°C); cleaning water, up to 200°F (93°C); dry air, up to 220°F (104°C).
• Allow Sika Thoroseal®-582 F to cure 7–10 days before immersion in water.
• On all projects, it is recommended that a sample be prepared on-site and approved prior to the commencement of the work. The site sample should confirm the color, texture, and workmanship required until the job is finished and accepted. Retain the sample until final approval is secured.
• Not intended as a decorative finish coat.
• Proper application is the responsibility of the user. Field visits by Sika personnel are for the purpose of making technical recommendations only and not for supervising or providing quality control on the jobsite.

1. Surface preparation is extremely important for proper adhesion. Substrates must be sound and free of dust, dirt, laitance, paints, oils, grease, curing compounds, or any other contaminants. Verify substrate has properly cured. Concrete should obtain 80% of design strength, typically achieved within 3–14 days. If efflorescence is present, mechanically remove it before proceeding. For extreme cases where this is not adequate, contact Technical Service.
2. Patch all holes and non-moving cracks before installation with the appropriate Sika product.
3. Relieve hydrostatic pressure in concrete block with weep holes.
4. Roughen or brush blast extremely smooth surfaces such as precast and cast-in-place concrete to ensure good mechanical adhesion of Sika Thoroseal®-582 F.
5. Completely saturate the substrate with water and allow the surface to dry before the application starts. A damp surface will prevent surface drag on the material, keep the substrate cool, and eliminate flash drying.

1. Mix Sika Thoroseal®-582 F with a mixing liquid consisting of a blend of Sika Thoroseal® Acryl 60 diluted with water. The maximum dilution ratio is one part Sika Thoroseal® Acryl 60 to three parts water. Approximately 6 quarts (5.7 L) of mixing liquid is needed per 50 lbs (22.7 kg) of powder. Water demand may vary with ambient temperatures and humidity levels.
2. For best results, mix Sika Thoroseal®-582 F with a slow-speed drill and mixing paddle. Gradually add the powder to the mixing liquid while the drill is running.
3. When properly blended, Sika Thoroseal®-582 F will have the lump-free consistency of smooth, heavy batter.
4. Allow the mixed Sika Thoroseal®-582 F/Sika Thoroseal® Acryl 60 to rest undisturbed for a minimum of 10 minutes to fully wet out all the powder. Then mix the wet mixture and apply. A small amount of mixing liquid can be added to the mixture.

1. Apply Sika Thoroseal®-582 F with a tampico brush or broom or equivalent stiff fiber brush or textured spray equipment. Spray applications of the first coat require back brushing or brooming to properly fill voids and achieve uniformity and optimum adhesion.
2. It is essential to work the first coat thoroughly into the substrate to completely fill and cover all voids, holes, and nonmoving cracks. Finish with a horizontal stroke for an even coat.
3. Allow to cure for 24 hours, then apply the second coat and finish with a vertical stroke. Above grade, the second coat can be replaced with a Sika high-build architectural coating to achieve better color uniformity.