Sika Thorocoat®-200 LR

Sika Thorocoat®-200 LR is a proprietary blend of acrylic polymers with special additives dispersed in a water base.

1 year when properly stored

Store in unopened containers in a cool, clean, dry area. Keep from freezing.

8.8–9.3

Elongation at break

2–4 hours at 70 °F (21 °C) and 50% relative humidity. Lower surface or air temperatures and higher relative humidity will extend the drying time.

• Do not apply when the substrate or ambient temperature is 40 °F (4 °C) or below or is expected to fall below 40 °F (4 °C) within 24 hours after application.
• Sika Thorocoat®-200 LR is not intended for use as a horizontal traffic-bearing coating.
• Apply a 4 by 4 ft (1.2 by 1.2 m) test area to verify acceptable color, texture, and adhesion before proceeding with any project. The test method for measuring adhesion is ASTM D 3359, Measuring Adhesion by Tape Method A. On the 0–5 scale, a minimum adhesion rating of 4A is required.
• Do not thin the material.
• For professional use only; not for sale to or use by the general public.
• Make certain the most current versions of the product data sheet and SDS are being used.
• Proper application is the responsibility of the user. Field visits by Sika personnel are for the purpose of making technical recommendations only and not for supervising or providing quality control on the jobsite.

1. Surfaces should be clean, sound, and free of all bond-inhibiting contaminants.
2. Mildew and fungus must be completely removed before application of Sika Thorocoat®-200 LR.
3. Concrete substrates should be fully cured.
4. Repair any holes, spalled and damaged concrete with appropriate Sika repair materials. Allow appropriate cure time prior to coating.
5. Remove any protruding concrete accessories and smooth out any surface irregularities.
6. High-pressure power wash surface (or abrasive blast on hard, dense surfaces) to create a profile of SP 3, per ICRI Guide 310.2.
7. Some stains may require chemical removal. Neutralize any cleaning compounds used and rinse with clean water.
8. Check adhesion of old coatings according to ASTM D 3359, Measuring Adhesion by Tape Test Method A.
9. Remove any blisters or delaminated areas and sand edges to smooth rough areas and provide a transition to old paint areas.
10. Treat cracks greater than 1⁄32" with Sika Thorocoat®-746 Knife Grade or SikaWall® FL 748. Treat cracks larger than ¼" as expansion joints and fill with appropriate Sika sealant.
11. New CMU must have a base coat of Sika Thorocoat®-749 Block Filler.

1. Prior to use, mix Sika Thorocoat®-200 LR at a slow speed with a drill and mixing paddle to ensure uniform color dispersion and minimize air entrapment.
2. In multi-pail applications, mix the contents of each new pail into the partially used previous pail to ensure color consistency and smooth transitions from pail to pail.

1. Apply Sika Thorocoat®-200 LR by brush, spray, roller, or spray-and-backroll.
2. Maintain proper uniform wet-film thickness (WFT) during application to ensure the performance characteristics desired (see yield rates section).
3. Always work to a natural break and maintain a wet edge during application.
4. For uniformity of color, application techniques must be consistent throughout the project.

Roller

1. Use a quality ¾–1¼" nap roller cover.
2. Completely saturate the roller and keep it loaded with the coating to build the required mils—never dry roll.
3. Cross roll, maintaining a wet edge, to achieve uniform thickness. Backroll in one direction for a consistent appearance.

Spray

1. Equipment is available for spraying Sika Thorocoat®-200 LR. Contact the equipment manufacturer for further recommendations.
2. Backrolling in one direction after spray application is recommended to achieve uniform film thickness.

Brush

1. Application by brush is recommended only for small inaccessible areas, e.g., on touch-ups.
2. Use only a nylon brush.

Clean all tools and equipment immediately with water. Cured material may be removed by mechanical means.