Product Data Sheet
Show all documents

SikaCem®-190 Concrete Control

A non-film forming, low VOC, amorphous colloidal silica topical additive applied to freshly placed concrete that maintains adequate moisture while reducing the risk of concrete setting prematurely

SikaCem®-190 Concrete Control is a non-film forming, low VOC, amorphous colloidal silica topical additive (evaporation retardant and finishing aid) that is ideal for all decorative and colored concrete applications. Apply during floating and troweling of freshly placed concrete to control moisture loss. This allows proper hydration of the cement that will extend workability and makes finishing concrete flatwork easier and faster under adverse conditions such as wind, sun, high temperatures, or low humidity.   SikaCem®-190 Concrete Control lubricates the surface and increases cream for a smoother finish, which makes troweling easier and faster. Colloidal silica densifies and improves surface consolidation resulting in increased compressive strength and abrasion resistance. SikaCem®-190 Concrete Control minimizes the potential for cold joints checking, crazing, curling, dusting, stains, and efflorescence on both standard and colored concrete.

  • Extended concrete workability
  • Lubricates concrete surface
  • Promotes proper hydration
  • Reduces surface crazing
  • All-weather concrete treatment
  • Reduces efflorescence
  • Reduces cured surface staining
  • Casting bed release friendly
  • Improves abrasion resistance
  • Promotes cleaner control joint cuts
  • Chemically reacts with entire mix design
  • Promotes flatter, thicker, denser cream cap
  • Supports consistent FF/FL numbers
Product Data Sheet
Show all documents

Usage

  • Decorative concrete
  • Concrete slabs
  • Polished concrete
  • Driveways and sidewalks
  • Interior or exterior concrete
  • Parking garages
  • Industrial floor slabs
  • Bridges and roads
 

Advantages

  • Extended concrete workability
  • Lubricates concrete surface
  • Promotes proper hydration
  • Reduces surface crazing
  • All-weather concrete treatment
  • Reduces efflorescence
  • Reduces cured surface staining
  • Casting bed release friendly
  • Improves abrasion resistance
  • Promotes cleaner control joint cuts
  • Chemically reacts with entire mix design
  • Promotes flatter, thicker, denser cream cap
  • Supports consistent FF/FL numbers

Packaging

5 gal. (18.9 L) fill in 5 gal. (18.9 L) plastic pail

55 gal. (208.2 L) fill in 55 gal. (208.2 L) steel drum

Product Details

Sustainability / Certifications / Approvals

APPROVALS / STANDARDS

  • ASTM E96/E96M-10 - Standard Test Methods for Water Vapor Transmission of Materials
  • ASTM C944/C944M-19 - Standard Test Method for Abrasion Resistance of Concrete or Mortar Surfaces by the Rotating-Cutter Method
  • ASTM C779/C779M-12 - Standard Test Method for Abrasion Resistance of Horizontal Concrete Surfaces
  • ASTM C1583/C1583M-20 - Standard Test Method for Tensile Strength of Concrete Surfaces and the Bond Strength or Tensile Strength of Concrete Repair and Overlay Materials by Direct Tension (Pull-off Method)
  • USDA Compliant
  • FDA Approved
 
Product Information

Chemical Base

Colloidal Silica

Shelf Life

24 months in original unopened container

Storage Conditions

Store in original, unopened containers in a well-ventilated, cool, dry location at temperatures between 40-100°F (4-38°C). Do not freeze. Do not break seal until product is ready for use. Maintain unused product in the original container.

Application

Consumption

Coverage

Apply at a rate of 1200 sq. ft./gal. (29.5 sq. m/L) per application.

 

Recommended Applications:

Broomed Finished Concrete

2
Stamped Concrete2

Color Hardened Concrete

2
Trowel Finished Concrete3
Application steps

EQUIPMENT

Use a high-volume, low-pressure, manual or commercial grade sprayer or pump up sprayer capable of spraying a fine mist.

MIXING

SikaCem®-190 Concrete Control is ready to use and requires no blending or dilution. Mild agitation is recommended before usage.

APPLICATION

SikaCem®-190 Concrete Control must be worked into the surface immediately after application. Apply SikaCem®- 190 Concrete Control using an automatic or low pressure pump sprayer. A fan or cone tip is recommended for even application. SikaCem®-190 Concrete Control can also be applied using the water tanks of a ride on trowel.

 

Trowel Finished Concrete

Spray apply uniformly onto the concrete surface in three equal applications as follows:

  • First application should be applied directly after the screed and before bull floating
  • Second application shall be applied just before the first panning
  • Third application shall be applied after panning is complete, during the finishing stage

 

Trowel Finish Concrete-Finishing Recommendations:

  • Follow industry best practice/procedures to begin the finishing process as you would on a standard pour
  • Machine panning is not recommended for exterior/air entrained concrete
  • Finish by burning/burnishing the floor to desired level

 

Broom Finished Concrete

Spray apply uniformly onto the concrete surface in two equal applications as follows:

  • First application should be applied directly after the screed and before bull floating
  • Second application shall be applied before edging and refloating, prior to brooming

 

Stamped or Color Hardened Concrete

Spray apply uniformly onto the concrete surface in two equal applications as follows:

  • First application shall be applied directly after the screed and before bull floating
  • Second application shall be applied before edging and refloating, prior to stamping or texturing

CLEANING OF TOOLS

Clean sprayers with warm, soapy water following use.

Documents