LITHOCHROME® Chemstain® Classic

LITHOCHROME® Chemstain® Classic complies with applicable air quality management regulations.

A corrosive, acidic, solution of metallic salts. FOR PROFESSIONAL USE ONLY.

2 years from the date of manufacture.

Store closed, upright, and only in original containers below 120°F (49°C).

Coverage Rates

Coverage will vary widely depending on the porosity and texture of the surface, composition and age of the concrete, surface preparation and application technique. Typical coverage rates are 200–300 square feet per gallon (4.9–7.4 m²/L). For deep or high intensity effects, a second application should be performed.

LITHOCHROME® Chemstain® Classic is corrosive. Read and understand this entire document and the product SDS before using this product. Always wear personal protective equipment when handling or using this product. If using spray equipment, always wear protective respirator, and mask adjacent areas to protect property from overspray. Never use high pressure spray equipment.

Stain can be applied using acid-resistant garden type pump sprayer with a conical tip, then worked into the surface with soft nylon brushes, mops, or lamb wool applicators. Avoid stiff bristles that can flick stain onto unwanted areas. An additional sprayer, mop and pail will be needed to apply and remove neutralizing or rinsing solutions. An industrial vacuum can be used to remove neutralized rinse water.

Factors Influencing Final Color & Appearance

The final color and appearance will be influenced by the concrete age, composition, technique used to finish the concrete, and application technique. Application to undisturbed slabs will be more paint like. Application to slabs with the top paste layer removed will be grainier. Variations in concrete finishing will become color swirls and variegations. Stain application to dry or wet surfaces will alter color development, as will the amount of stain applied and the amount of effort used to work stain into the surface. Take care not to over apply or overwork stain into the surface, or color may not remain after rinsing,

Jobsite Test Sections

Verify and approve suitability and appearance by making jobsite test sections prior to general application. Apply each chemical stain color onto each type and age of concrete or topping surface, and use each sealer technique that is to be used. Test sections must be of adequate size to be representative and be produced by the same workers who will apply product to the larger job. Test completed systems for wet and dry slip resistance to ensure they are safe. Do not proceed with products, techniques, or finishing systems that do not meet required safety specifications or site owner approval.

Stain Application

Chemical stain is permanent. Mask all areas not to be stained to safeguard against splashes, overspray, and runoff from application, neutralization, or residue removal. Only work in a well ventilated area. Wear all required safety equipment. Keep a five gallon pail of water with 1 pound of baking soda added to neutralize spills or accidental contact. Take care not to allow tape adhesive to interfere with surfaces to be stained.

The following 8 steps have proven successful for floors in a wide range of conditions.

1. Optional Pre-wetting of surface.

Many artisans prefer to pre-wet the concrete prior to stain application. This maximizes color penetration and variegations. Spray clean water to saturate the concrete surface. Remove puddles by spreading water or soaking up with a clean mop. The surface should now be cool, damp to the touch, yet not allow a towel to readily absorb water.

2. Apply the LITHOCHROME® Chemstain® Classic. This can be done with an acid resistant low pressure garden sprayer, mop or broom. Apply in a circular motion to just saturate the surface. LITHOCHROME® Chemstain® Classic should fizz or effervesce when it first comes in contact with the concrete.

3. Immediately work in stain. Use a foam, lamb's wool, or soft nylon bristle broom working in circular motions to avoid the creation of lap marks. Do not walk on recently stained areas or footprints will result.

4. Allow surfaces to dry. This will take about 4 hours depending on weather conditions and water used in step 1.

5. Apply a second coat if desired and allow it to dry.

6. Neutralize the surface: Use a solution of 1 pound of baking soda per 5 gallons of water. Apply this with a clean garden sprayer. Move neutralization liquid across the surface with a wet mop or soft broom in a circular motion. Neutralization is complete when surfaces are saturated and no effervescence is seen.

7. Remove pigment residue. Use a soft broom or mop and a wet-dry vacuum moving in circular motions to avoid creating lap lines. Rinse surfaces until all easy to remove residue is removed. If a second complimentary color is to be used, apply it at this stage. Failure to remove all residue prior to sealing the surface can cause loss of adhesion, peeling, or reduced sealer durability. When complete, little to no residue should appear after rubbing with a clean cloth.

8. Allow to dry and apply sealers/topcoats as desired.

For Vertical Applications: Apply by garden sprayer consistently from the bottom up or the top down. Brush out drips immediately. Allow to dry at least 4 hours before neutralization and rinsing. Seal if desired.

Clean equipment with water and baking soda solution to neutralize residual stain. Rinse with clear water.