Product Data Sheet Safety Data Sheet Show all documents
DriTac® Repair Adhesive Solid Wood

DriTac® Repair Adhesive Solid Wood

Solid Wood and Bamboo Floor Repair Adhesive

Sika-DriTac has developed a repair system to correct hollow spots and popping conditions for solid wood and bamboo flooring installations. After years of successful repairs with our Engineered Wood Floor Repair Kit and constant requests from installers to design a repair kit for solid wood and bamboo floors, Sika-DriTac is here to once again fix the problem and provide the solution for voids, hollow spots and popping conditions in wood flooring installations.

• Functional and easy to use for both the professional flooring installer and the “do it yourselfer”
• Hollow spot or void beneath the flooring is completely filled with the repair adhesive, truly repairing the problem! (Epoxy repair kits only tack down a small section of the problem area)
• Drill bit and applicator tips are much smaller in diameter than conventional repair kits, creating a smaller hole which is easily hidden with wood putty
• No need to weigh down the repaired area
• Cost per repair is a fraction of the cost of epoxy
• Floor can be walked on immediately after the repair. No set up time is required!
Product Data Sheet Safety Data Sheet Show all documents

Usage

• Bamboo
• Solid Wood
• Multi-Ply Engineered Plank  

Advantages

• Functional and easy to use for both the professional flooring installer and the “do it yourselfer”
• Hollow spot or void beneath the flooring is completely filled with the repair adhesive, truly repairing the problem! (Epoxy repair kits only tack down a small section of the problem area)
• Drill bit and applicator tips are much smaller in diameter than conventional repair kits, creating a smaller hole which is easily hidden with wood putty
• No need to weigh down the repaired area
• Cost per repair is a fraction of the cost of epoxy
• Floor can be walked on immediately after the repair. No set up time is required!

Packaging

• 1- Injection Gun 
• 3- Mixing Nozzles
• 2- Drill Bits
• 2- Adhesive Catridges
• 3- Applicator Tips
• 4- Wood Dowels
• 1- Dowel Punch

• Replenish Pack Available (SW-2): includes all components except injection gun.

Product Details

Product Information

Shelf Life

24 Months

Storage Conditions

+41°F (+5°C) to +77°F (+25°C) The product must be stored in original, unopened and undamaged sealed packaging in dry conditions.

Application

Application steps

APPLICATION INSTRUCTIONS

  • Locate loose area(s) in the wood and outline with blue releasable tape. Prepare all hollow areas at the same time. Doing all repairs in a short time period will prevent the syringe from clogging. Drill hole(s) with a 3/32” drill bit, (provided in this system), in the area outlined by the blue tape. There may be a need for more than one hole per loose area depending upon size. For larger areas, at least two holes are recommended. Drill one hole at one side of the hollow area and a second hole at the other side.
  • Place the dual component cartridge kit in a dual plunger manual dispensing gun and remove the end cap from the cartridge. Attach a static mixer nozzle to the cartridge. Keep cartridge upright until use. Bleed off any air inside the cartridge by keeping the mixer nozzle upward and slightly squeezing handle. Dispense the material by working the trigger of the gun. Dispense and properly dispose of a small amount of material to start the material mixing. This is done to ensure complete product mix. Proceed with application. To stop dispensing, release pressure by pressing the lever on the gun and pulling back the plungers.
  • Once the void is completely filled use the dowels provided as a plug for the hole(s) drilled. This will keep the adhesive securely under the floor. The dowel is slightly oversized and needs to be tapered with a knife or sandpaper to properly fill the hole. Tap the dowel into the hole and cut it off even with the floor. Use the dowel punch provided in this system to lower the dowel below the surface of the flooring. Putty the hole with wood filler that blends with the floor color.
 

Documents