Product Data Sheet Safety Data Sheet Show all documents
Ply Sheet HA 87

Ply Sheet HA 87

Hot applied SBS modified bitumen fiberglass reinforced ply sheet

Ply Sheet HA 87 is a 87 mil (2.2 mm) thick hot applied SBS modified bitumen fiberglass reinforced ply sheet for use within Sarnafil® hybrid roofing systems. Ply Sheet HA 87 can also be used as a vapor retarder in Sarnafil® and Sikaplan® roofing systems.  It can be left exposed for up to six (6) months.

  • Superior tensile strength
  • Weathering surface allows for exposure for up to six (6) months
  • Fiberglass reinforcement provides dimensional stability
  • Fine mineral aggregate (sand) topside accepts approved urethane adhesives for membrane attachment
Product Data Sheet Safety Data Sheet Show all documents

Usage

  • Ply sheet within Sarnafil hybrid roofing systems
  • Vapor retarder within Sarnafil and Sikaplan roofing systems
     
AREAS OF APPLICATION
  • Sarnafil hybrid roofing systems over light weight insulating concrete, cementitious wood fiber deck and metal deck
  • Vapor retarder direct to structural concrete deck and DensDeck® Prime
 

Advantages

  • Superior tensile strength
  • Weathering surface allows for exposure for up to six (6) months
  • Fiberglass reinforcement provides dimensional stability
  • Fine mineral aggregate (sand) topside accepts approved urethane adhesives for membrane attachment

Packaging

39.4" (1 m) x 49.2 ft (15 m) roll, 101 lbs (45.8 kg) per roll

30 rolls per pallet

Product Details

Sustainability / Certifications / Approvals

APPROVALS / STANDARDS

  • FM Global
  • Underwriters Laboratories
  • Florida Building Code
  • Meets ASTM D6163, Type I, Grade S
  • Tested according to ASTM E108
  • Tested according to ANSI/FM 4474 for wind uplift
  • Tested according to Miami-Dade TAS 114 for wind uplift

 
Product Information

Chemical Base

SBS polymer modified bitumen with a fiberglass mat reinforcement and fine mineral aggregate (sand) topside and polyolefin burn-off film underside

Shelf Life

N/A

Storage Conditions

Store rolls on end and maintain in an upright position to prevent damage. Store rolls in a clean dry location and cover as necessary to protect rolls from environmental damage such as extreme cold, heat, or moisture.

Thickness

87 mil (2.2 mm)

(ASTM D-5147)

67 mil (1.7 mm) at selvage, minimum

(ASTM D-5147)

Mass per Unit Area

62.6 lb/100 ft2 (3054 g/m2)

(ASTM D-5147)
Technical Information

Tensile Strength

Peak load @ 0°F (-18°C)

Machine Direction

Cross Machine Direction

100 lbf/in (17.5 kN/m)

90 lbf/in (15.8 kN/m)

Peak load @ 73.4°F (23°C)

Machine DirectionCross Machine Direction

50 lbf/in (8.8 kN/m)

40 lbf/in (7.0 kN/m)

Elongation

Elongation at peak load @ 0°F (-18°C)

Machine Direction

Cross Machine Direction

4%

4%

Elongation at peak load @ 73.4°F (23°C)

Machine Direction

Cross Machine Direction

5%

4%

Ultimate elongation @ 73.4°F (23°C)

Machine Direction

Cross Machine Direction

45%

45%

Dimensional Stability

Machine Direction

Cross Machine Direction

<0.1%

<0.1%

Tear Strength

Machine Direction

Cross Machine Direction

60 lbf (267 N)

60 lbf (267 N)

Low Temperature Bend

Machine Direction

Cross Machine Direction

-15°F (-26°C)

-15°F (-26°C)

Service Temperature

Compound Stability

250°F (121°C)

(ASTM D-5147)

 

Application

Application steps

SUBSTRATE PREPARATION

All surfaces must be clean, sound, dry, and free of loose materials or contaminants such as water, frost, ice, oil and grease that would interfere with proper adhesion and compromise the performance of the product.

 

In accordance with the ICRI Technical Guideline No. 310.2R-2013, newly poured concrete surfaces must be finished by forming, wood float, steel or power trowel, or broom finished to meet the equivalency of a CSP type surface between a rating of 2 – 5.

 

Application to structural concrete surfaces and DensDeck Prime require priming with Vapor Retarder Primer TA or Vapor Retarder Primer BE.  See Vapor Retarder Primer TA or Vapor Retarder Primer BE product data sheet for additional information.

APPLICATION

Prior to installation, unroll Ply Sheet HA 87 onto the roof surface and allow it to relax. Place Ply Sheet HA 87 in desired position and back roll the product. Apply a full mopping of Type III or Type IV asphalt in accordance with industry standards at a minimum rate of 25 lbs per 100 square feet (1.2 kg/m²). Install Ply Sheet HA 87 so that there are no significant and avoidable air spaces between the ply sheet and the substrate.

    

Ply Sheet HA 87 can be installed with Sika’s cold applied vapor retarder adhesives. See Sika’s vapor retarder adhesive product data sheets for additional information.

   

Overlap side laps 3" (76 mm) and end laps 6" (152 mm)

   

COVERAGE
161 ft2 (15 m2) per roll

Documents