Product Data Sheet
Show all documents
Sikalastic®-715 Textured TopCoat

Sikalastic®-715 Textured TopCoat

Single component, integrally textured, elastomeric, traffic bearing wear and top coat

Sikalastic®-715 Textured TopCoat is a single component, UV-resistant, aromatic, moisture cured, elastomeric polyurethane coating intended for use as the traffic bearing wear and top coat over polyurethane waterproofing membrane for pedestrian and vehicular traffic bearing applications, and as a protective top coat over polyurethane waterproofing membrane under a separate wearing course such as concrete or asphalt pavement, and tile in a setting bed.

  • Excellent crack-bridging properties and flexibility, even at low temperatures
  • Outstanding resistance to abrasion and wear
  • Resistant to water and de-icing salts
  • Alkaline resistant
  • UV resistant
  • Range of standard colors
Product Data Sheet
Show all documents

Usage

  • Multi-story parking garages
  • Parking decks and ramps
  • Foot bridges and walkways
  • Mechanical rooms
  • Stadiums and arena
  • Plaza and rooftop decks
  • Balconies
 

Advantages

  • Excellent crack-bridging properties and flexibility, even at low temperatures
  • Outstanding resistance to abrasion and wear
  • Resistant to water and de-icing salts
  • Alkaline resistant
  • UV resistant
  • Range of standard colors

Packaging

5 gal. pails

Color

Gray, Charcoal and Tan

Product Details

Product Information

Shelf Life

12 months year in original, unopened containers

Storage Conditions

Store dry at 40–95 °F (4–35 °C). Condition material to 65–85 °F (18–30 °C) before using

Solid content by volume

76 %

(ASTM D-2697)

Volatile organic compound (VOC) content

232 g/l

(ASTM D-2369-81)

Viscosity

3000 +/- 1500 cps @ 800F
Technical Information

Shore A Hardness

90 +/- 5 (75 °F (24 °C) and 50 % R.H.)

(ASTM D-2240)

non seeded film

Tensile Strength

3200 +/- 300 psi (75 °F (24 °C) and 50 % R.H.)

(ASTM D-412)

non seeded film

Tear Strength

250 +/- 50 pli (75 °F (24 °C) and 50 % R.H.)

(Die C, ASTM D-624)

non seeded film

Chemical Resistance

Resistant to de-icing salts, and alkaline concrete and cementitious mortars/tile adhesives cure.

Application

Consumption

Coverage

80 sf/gal at 16 wet mils (12 dry mils)
66 sf/gal at 18 wet mils (14 dry mils)
58 sf/gal at 20 wet mils (16 dry mils)

Coverage rates provided are intended to achieve required wet film thickness under optimal conditions. Additional material may be required depending on substrate surface roughness and porosity, material substrate and air  temperatures, and other site-dependent factors. This will result in a lower coverage rate.
Application steps

MIXING

Thoroughly mix for 3 minutes using a mechanical mixer (Jiffy) at slow speed until a homogenous mixture and uniform color is obtained. Make sure to scrape the solids and the aggregate from the bottom and sides of the pail. The aggregate should be evenly diffused in the resin. Use care not to allow the entrapment of air into the mixture.

APPLICATION

Wear coat: Apply at the recommended coverage rate 20 mils wet (58 sf/gal) using a 1/8” or 3/16” notched squeegee or trowel, and backroll using nap roller 3/8” to uniformly backroll prior to applying topcoat. It should be backrolled two times, one perpendicular to the other.

  

Top coat: Apply at the recommended coverage rate 20 mils wet (58 sf/gal) using a 1/8” or 3/16” notched squeegee or trowel, and backroll using nap roller 3/8” to uniformly backroll . The Top coat should be backrolled two times, one perpendicular to the other. Allow coating to cure a minimum of 4 hours at 70 °F and 50 % R.H.; coating must be tack free before overcoating. Allow coating to cure for a minimum of 36 hours before opening to vehicular traffic

   

Accelerator: Sikalastic 700 ACL may be added to Sikalastic®-715 Textured TopCoat in order to speed cure time particularly in cold weather conditions. Mix thoroughly prior to application. Add a maximum of 1 quart to 5 gallons (or 1:20 ratio) and only to material that will be applied within 2–3 hours.

  

Removal

Remove liquid coating immediately with dry cloth. Once cured, coating can only be removed by mechanical means.

Documents