Sika Waterbar®-940

• ASTM D 638 : 91 (Tensile/ Elongation)
• US Corps of Engineers CRD-C572-74 (Alkali Resistance)
• Instron Tensometer (Extension/ Transverse Shear)

PVC-P (plasticized)

Up to 60 months from date of production.

Store in undamaged, unopened, original sealed packaging in dry conditions at temperatures between +5°C and +35°C. Protect from direct sunlight, heat and moisture.

Sika Waterbar®-940 IEJ:

Expansion bulb sections principally for expansion joints . With reinforced eyeleted fixing flanges for wiring the waterstop to surrounding rebar.

Sika Waterbar®-940 ICJ:

Plain web sections for construction / contraction joints, also with reinforced eyeleted flanges and grout check fins to prevent grout loss from formwork.With reinforced eyeleted fixing flanges for wiring the waterstop to surrounding rebar.

Sika Waterbar®-940 EEJ:

Sections have a flat top, wedged expansion box for positive anchorage and good seating of joint fillers, The bottom web in the expansion box is thinned to cater for excessive subsidence or seismic movement should it occur.

Sika Waterbar®-940 ECJ:

Sections are plain web incorporating grout check fins to prevent grout loss at formwork.

Sika Waterbar®-940 250 ICJ/X - 250 IEJ/X - 250 EEJ/X - 250 ECJ/X:

10 mm thick web profiles for applications where there is high water pressure or head of water in excess of 70 m. Internal profiles include reinforced eyeleted fixing flanges.

Intersection Pieces / Junctions:

Standard factory produced welded intersections are available for all Sika Waterbar®-940 profiles if needed:

+5°C min. / +35°C max.

• Heat welding equipment is required to enable site jointing to be carried out efficiently.
• Ensure that the mating surfaces of the waterstop are accurately aligned while the heater blade heats the waterstop to the necessary temperature for jointing.

• Sika Waterbar®-940 ICJ & IEJ profiles must be installed so they are securely held in the correct position whilst the concrete is poured.
• The concrete must be fully and properly compacted around the waterstops.
• Where reinforcement is present, an adequate clearance must be left between this and all waterstops to permit proper compaction of the concrete.
• The eyelets in the reinforced flanges of the ICJ and IEJ profiles allow them to be wired to the surrounding reinforcing steel. The eyelets are an integral part of the profiles and being placed outside the outer valves cannot create a water path around the profile or impair the efficiency in performance in any way. See typical detail below.
• Sika Waterbar®-940 ECJ & EEJ profiles when used on ground slab blinding concrete where a permanent, firm and stable support is given usually require no fixing.
• The profile is simply laid centrally over the line of the joint to be formed.
• Fixing to vertical shuttering is simplified by nailing with double headed nails through the outer reinforced flange to provide a firm fixing as shown below.

HEAT WELDING OF WATERSTOPS

• Make sure that the heater blade is clean, plug it into the correct voltage electricity supply and leave in a safe position to warm up.
• Ensure that the ends of the waterstop to be jointed are of the same width and profile; clean them with water or MasterTop THN 2 and dry them.
• Clamp them in the correct profile slots of the jig provided and cut both ends off square with a sharp knife, flush with the faces of the jig.
• Note: An allowance must be made for waste and for the 5 to 10mm that will be taken up by melting when calculating the length of waterstop required.
• Loosen the jig and slide them back so that approximately 10mm of each waterstop end projects and then clamp the jig tightly in position.
• Position the heater blade on the bars between the jigs and slide them together until the waterstop ends are pressed firmly against the sides of the blade. The PVC should melt without burning or charring. Hold the jig firmly in position until a bead of molten PVC approximately 3mm in diameter appears along either side of the heater blade.
• Slide the jig apart a little and remove the heater blade with an upward movement. This will ensure that it takes as little PVC as possible with it. Quickly joint the molten ends by sliding the jig together and exerting pressure. Approximately 20 seconds to allow the molten PVC to fuse completely. Switch off the heater blade. While it is still hot, clean thoroughly with emery paper or a wire brush ready for the next joint. Unclamp the jig and carefully remove the waterstop. Do not flex the joint until it has cooled. The joint is now complete. When cold, test it by flexing the waterstop several times.