
Sarnafil® S 327-80 Textured
Sarnafil® S 327-80 Textured Roof Membrane is a PVC thermoplastic membrane produced with an integral polyester reinforcement for high strength, with heat‐weldable seams, and a textured surface.
- Embossed surface
- Excellent tear strength resistance
- Hot‐air welded seams for long‐term performance
- Superior fire resistance
- Proven membrane performance
Usage
Mechanically attached applications with various fastening methods, over various substrates. AREAS OF APPLICATION- In-seam disc systems
- In-seam batten, double-weld systems
- RhinoBond® systems
- New construction and reroofing
Advantages
- Embossed surface
- Excellent tear strength resistance
- Hot‐air welded seams for long‐term performance
- Superior fire resistance
- Proven membrane performance
Packaging
80 mil (2.0 mm) Membrane*
6.56 ft x 50 ft (2 m x 15 m) roll, 168 lbs (76 kg) per roll
19 rolls per pallet
* Made to order, minimum volume required, extended production lead times. Consult with Sika – Roofing representative for further information.
Colour
- Top: Gray
- Bottom: Dark Gray
Product Details
APPROVALS / STANDARDS
- FM Global
- Underwriters Laboratories
- ICC Code Compliance – ESR 1157
- Miami‐Dade County
- Florida Building Code
- LEED / Green Globes
- NSF/ANSI 347 : Platinum Certified
Chemical Base
High quality, PVC membrane containing ultraviolet light stabilizers, flame retardant and polyester scrim reinforcement
Reinforcing Material
Polyester
Shelf Life
N/A
Storage Conditions
Store rolls on pallets and fully protected from the weather with clean canvas tarpaulins. Unvented polyethylene tarpaulins are not accepted due to the accumulation of moisture beneath the tarpaulin in certain weather conditions that may affect the ease of membrane weldability.
Top surface
Textured
Overall Thickness
80 mil (2.0 mm), minimum thickness 45 mil | (ASTM D-751) (ASTM Type III D-4434 Spec. Requirement) |
Thickness Above Scrim
Exceed 16 mil | (ASTM D-7635) (ASTM Type III D-4434 Spec. Requirement) |
Resistance to Static Puncture
Pass 33 lbf (15 kg) | (ASTM D-5602) (ASTM Type III D-4434 Spec. Requirement) |
Resistance to Dynamic Puncture
Pass 14.7 ft-lbf (20 J) | (ASTM D-5635) (ASTM Type III D-4434 Spec. Requirement) |
Tensile Strength
325 lbf (1445 N) 200 lbf (890 N) | (ASTM D-751) (ASTM Type III D-4434 Spec. Requirement) |
Linear Dimensional Change
-0.01% 0.5% | (ASTM D-1204) (ASTM Type III D-4434 Spec. Requirement) |
Tear Strength
49 lbf (218 N) 45 lbf (200 N) | (ASTM D-1004) (ASTM Type III D-4434 Spec. Requirement) |
Seam Strength
Pass 75% of original1 | (ASTM D-751) (ASTM Type III D-4434 Spec. Requirement) |
1 Failure occurs through membrane rupture not seam failure.
Low Temperature Bend
Pass Pass ‐40°F (‐40°C) | (ASTM D-2136) (ASTM Type III D-4434 Spec. Requirement) |
Retention of Properties after Heat Ageing
Tensile Strength, % of original: Pass Elongation, % of original: Pass Tensile Strength, % of original: 90 Elongation, % of original: 90 | (ASTM D-3045) (ASTM D-751) (ASTM Type III D-4434 Spec. Requirement) |
UV Exposure
10,000 hours 5,000 hours | (ASTM G-154) (ASTM Type III D-4434 Spec. Requirement) |
Cracking (7x magnification) | None |
Discoloration (by observation) | Negligible |
Ceazing (7x magnification) | None |
Weight Change after Immersion in Water
Pass ± 3.0% | (ASTM D-570) (ASTM Type III D-4434 Spec. Requirement) |
Application
APPLICATION
Sarnafil S 327 is rolled out onto the insulation board or acceptable substrate, flipped over in order to reveal textured side of membrane as the top surface, fastened to the roof deck with appropriate plates and fasteners, and heat‐welded together by trained operators using hot‐air welding equipment. Please consult Sika’s Specification or Applicator Handbook for detailed installation procedures.